F-Body保存会 総合掲示板

アメ車に関すること、カマロ、ファイアーバードに関すること、
DIYやカスタム、メンテの話、そしてその他の話題も含めて、何でも書き込みOKの掲示板です。
初めての人もネチケットを守って、お気軽にご参加ください。


掲示板使用上の注意    アイコン一覧
  新規投稿 ┃ツリー表示 ┃スレッド表示 ┃一覧表示 ┃トピック表示 ┃番号順表示 ┃検索 ┃設定 ┃過去ログ ┃ホーム ┃チャット  
469 / 1199 ←次へ | 前へ→

【731】ラジエター?ラジエーター?ラヂエーター?
←back ↑menu ↑top forward→
3rdハニー号  ハニー号 E-MAIL  - 08/6/5 23:12 -

引用なし
パスワード

[添付]〜添付ファイル〜
・名前 : 20080601.JPG
・サイズ : 67.0KB
   またまたロードマスターで申し訳ないです。
ラジエーターからの水漏れがあり、社外品を輸入して早速取り付け。
『Direct Fit』との事でしたが若干仕様が違いまして、サブタンクからの vent hose(オーバーフローホース?)の取り付け先がありません。
説明書には多分「もしベントホースがあればinlet heater hoseかthrottle body heater outletにティーでつなげ」って書いてあると解釈しまして、その通りに配管したのですが水温が上がりまくり!
っていうかラジエーターに熱いクーラントが流れて行きません。

かなり慌てまして、
1、ラジエーターに直ホースで流水し流量チェック
2、サーモスタット煮沸試験
3、ウォーターポンプ新品交換
をしましたがどれも問題ナシでした。

仕方なく漏れてるラジエーターに戻すと何事もなかったように正常に…
(ここでWAKOSの漏れ止めに登場願いました)

そこで説明書の解釈が間違ってないか気になりまして、原文のまま掲載しますのでどなたか間違いがあればご指摘願います。
(OCRを使ってるので誤字があったらごめんなさい)

The failed radiator being replaced by this new Ready Rad radiator may have a
vent hose connecting the outlet tank to the overflow bottle, which this new radiator
does not require, if your failed radiator does not have this hose connecting the
radiator outlet tank to the overflow bottle, disregard these instrucctions and install
the new radiator in the usual manner.

If your radiator has the vent hose, the hose needs to be plugged at the overflow
bottle. This overflow bottle was connected to the cooling system at three points.
The connection to the top of the outlet tank has been eliminated. There are still two
connections to the cooling system: a tee connection to the inlet heater hose and a
connection to the throttle body heater outlet, so you will fill the system through the
overflow bottle as before. The vent hose was never there to fill the system: it was
designed strictly for overflow. Removing the overflow hose actually helps heater
warm-up performance.

You can complete the installation in the following manner:

1) A10 mm diameter bolt (not included) about 1/2 to 1/3 inches long (12 to 19mm)
 Will be used to plug the hose
2) The hose needs to be cut as close as possible to the overflow bottle, still allowing
  the 1 Omm diameter bolt to be inserted in the hose to act as plug.
3)Use the clamp that connects the hose to the outlettank on the old radiator
 to hold the 1 Omm bolt in place.
4) Make sure there is no excessive movement in the cut hose once it is plugged.
 If there is, cut the hose shorter, or attach it to the vehicle with tape or cable tie.

  

添付画像
【20080601.JPG : 67.0KB】
445 hits
<Mozilla/4.0 (compatible; MSIE 6.0; Windows NT 5.1; SV1; .NET CLR 2.0.50727; .N...@p1200-ipbf52sasajima.aichi.ocn.ne.jp>

【731】ラジエター?ラジエーター?ラヂエーター? ハニー号 08/6/5 23:12 3rdハニー号[添付]
【734】Re:ラジエター?ラジエーター?ラヂエーター? KID 08/6/6 0:25
【736】Re:ラジエター?ラジエーター?ラヂエーター? ハニー号 08/6/6 1:28 3rdハニー号
【737】Re:ラジエター?ラジエーター?ラヂエーター? KID 08/6/6 3:17

469 / 1199 ←次へ | 前へ→
  新規投稿 ┃ツリー表示 ┃スレッド表示 ┃一覧表示 ┃トピック表示 ┃番号順表示 ┃検索 ┃設定 ┃過去ログ ┃ホーム ┃チャット  
ページ:  ┃  記事番号:   
38230
(SS)C-BOARD v3.8(とほほ改ver2.1) is Free